top of page
MSD EFI MPFI Ignition Kit – Dual Sync Distributor + 6AL-2, Coil & Wires

This MSD Distributors

This distributor assembly produces a 1x camshaft position signal that is compatible with Gen III LS-series electronics.

0-12V hall effect camshaft position sensor

generates a 50% duty cycle (signal voltage high for 50% and signal low for 50%)shaft diameter measures 0.427 inch

bronze or melonized steel gear available separately

compatible with GM and aftermarket fuel management systems

The hold down clamp on this distributor is fixed. For easy cam signal adjustment, consider using a traditional style hold down clamp instead of the (removable) fixed clamp.

This MSD Distributors features an adjustable cam sync pickup so you can set it to your ECU's requirements (up to 60° BTDC).

Includes a non-magneticsync pickup and is equipped with a slip collar, iron gear and a race rotor.

Features: Must be used with an MSD 6, 7 or 8-Series Ignition.

Specs

Brand MSD

Category Ignition

Color Black

Distributor Type EFI Dual Sync

Emission Code 4

Product Type Cam Sync

Warranty Manufacturer's Limited 1 Year Warranty

UPC 08513202345Part Number 2345


6al msd Following the introduction of the 6AL-2, there will also be a 21st century version - a laptop programmable 6AL! The programmable 6AL-2 shares the same advanced features of the new 6AL-2.


This new ignition is based on the same output as the 6AL-2, but rather than rotary dials for rpm adjustments it sports a serial port that connects to a PC. Once you load MSD's Windows based software on your PC, you're ready to start mapping and programming. To start, you can get rid of the weights and springs that control the mechanical advance of your distributor. Go ahead and lock it out because you can now create a timing curve that allows you to manipulate the timing down to tenth of a degree increments every 100 rpm. The advantage is precise timing control, with the ability to ramp the timing in or retard it at exactly the rpm that you want it to move. Want more timing out for a start retard? Simply click the mouse and move a couple dots in position. Like a high speed retard? Clickity-click!


Another great feature is for the forced induction fans. The ignition features a timing curve based on boost so you can map out a timing curve based on boost pressure. The feature that most street guys will dig is the ability to pull timing out during the holeshot - and ramp it back in. Since many cars have more power than traction capabilities, being able to soften the power at the holeshot can help reduce the tire shredding off the line.


There are also three different rpm limits that can be set in 100-rpm increments; one for the burnout, one for the holeshot and of course a top end limit for overrev protection. If you have a nitrous shot you like to blast off now and then, the ignition has an activation wire that you tie into the nitrous wiring. When the nitrous is activate, the timing can be retarded instantly!


Highlights

All new housing, digital circuits and performance

Three Programmable rev control limits

Higher output with up to 135mJ and 535 volts

Accepts Hall-effect, points and mag pickup triggers

Managed by an efficient digital controller

Operating Specifications

Spark Energy: 135 mJ per spark

Primary Voltage: 535 Volts

Secondary Voltage: 45,000 Volts

Spark Series Duration: 20 degree Crankshaft Rotation

RPM Range: 12,500 RPM with 14.4 Volts

Voltage Required: 12-18 Volts, Negative Ground

Current Draw: .7 Amp per 1,000 RPM

Size: 7"L x 4"W x 2"H


MSD 82073 Blaster SS Ignition Coil Features:

Improved output coil for electronic ignitions, and MSD Ignitions

Efficient winding design and assembly create a compact housing

Primary and secondary windings are encased in Ciba polyurethane

70:1 turns ratio and lower primary resistance produce a high voltage output

Dupont Rynite housing with a tall tower and brass primary terminals

Tough, rigid housing with a tall tower and brass primary terminals

Blaster SS Ignition Coil

70:1 Turns Ratio

Windings Encased in Ciba Polyurethane

Tall Tower w/Brass Terminals

Compact Housing

Includes:

Coil Wire Boot & Terminal

Vibration Mounts

Male & Eyelet Connectors

Mounting Hardware

Maximum voltage: 40,000 Volts (Tested with 6AL Ignition)

Peak current: 300 mA

Spark duration: 220 uS


Taylor Taylor Spiro

Taylor Taylor Spiro-Pro Race-Fit Spiro-Wound core spark plug wire sets outperform the competition in both looks and performance at a price that you can afford. According to Taylor, Spiro-Pro is simply the best high performance 8mm wire you can buy and is a perfect choice for your race or street car. Their Spiro-Wound core is designed for use when RFI suppression is required for today's complex multiple spark discharge systems. Spiro-Pro features two layers of 100 percent silicone to withstand temperatures of up to 600 degrees F without the need for additional sleeving. Each wire is pre-terminated to a specific length—and features Taylor's all-silicone Pro Boots with double spring-locking spark plug terminals. They're available in a choice of colors. Order the set and options designed for your vehicle and engine application.

MSD EFI MPFI Ignition Kit – Dual Sync Distributor + 6AL-2, Coil & Wires

$1,350.00 Regular Price
$1,195.00Sale Price
Quantity
bottom of page